










Printed Fabric Petal Pendant Lamp
Size
Colour
| Brand | Vakkerlight |
|---|---|
| SKU | VKP1-2673-01 |
| Type | pendant Lamp |
| Colour | Beige |
| Variants | 3 |
A petal-form fabric pendant suspended from a retractable spring tube — the shade panels are cut from printed fabric and assembled into a layered bloom silhouette, with a scalloped lower hem and a solid wood bead drop at the centre. The spring tube suspension is the practical differentiator: it stretches and compresses to let you raise or lower the pendant by hand at any time, without tools or rewiring, to suit the activity below. A 3000K E26 or E27 LED bulb is included.
A 3000K warm-white E26 or E27 LED bulb ships with every pendant. Hang it, wire it, screw in the bulb, and it is ready. Any standard E26 or E27 bulb also fits the socket.
This pendant hardwires to a ceiling junction box. The black spring tube extends up to 1.5 m and compresses back toward the ceiling — pull the shade down to lower it, push up to raise it. A licensed electrician is recommended for the initial wiring. Always turn off power at the breaker before installation.
Petal Fabric Shade
Printed fabric panels assembled into a layered bloom form — scalloped lower hem and a solid wood bead drop at the centre bottom.
1.5 m Retractable Spring Tube
Pull down to lower, push up to raise — adjust the hanging height by hand at any time without tools or rewiring.
Solid Wood + Hardware
Solid wood bead drop and hardware fittings — warm natural accents that complement the printed fabric shade.
3000K Bulb Included
A warm-white E26 or E27 LED at 3000K ships in the box — no separate bulb purchase needed.
Soft Diffused Glow
The fabric shade diffuses light warmly downward — the printed pattern reads as a subtle texture when lit from within.
3 Sizes
Ø40 · Ø50 · Ø60 cm — suited to rooms of 110–195 sq ft (10–18 m²).
15.7″ wide. Over a 2-person table, bedside, or reading nook.
19.7″ wide. Versatile solo pendant over a 2–4 person table or compact island.
23.6″ wide. Over a 4–6 person table or bedroom focal point.
The black spring tube extends up to 1.5 m from the ceiling canopy. For dining tables, pull the shade so the bottom sits 70–80 cm (28–32″) above the tabletop. Push up to raise for ambient lighting.
The included 3000K warm-white LED is ready to use out of the box. To dim, swap for a Triac-dimmable E26 or E27 LED and pair with a Triac wall dimmer switch.
×
×
×
Dimensions — tap to enlarge
| Material | Printed fabric shade · Solid wood bead drop · Metal hardware |
| Finish | Cream printed fabric + natural wood + matte black hardware |
| Sizes | Ø40 cm · Ø50 cm · Ø60 cm — contact us for shade heights |
| Light source | E26 or E27 medium screw base · 3000K LED bulb included |
| Suspension | Retractable black spring tube · extends up to 1.5 m |
| Canopy | Matte black (all sizes) |
| Installation | Hardwired ceiling pendant (junction box required) |
| Voltage | AC 110–240 V · 50/60 Hz |
| Dimmable | Yes — replace included bulb with Triac-dimmable E26 or E27 LED + compatible dimmer |
| Recommended room size | 110–195 sq ft (10–18 m²) |
| Best for | Dining room, bedroom, living room — traditional, French country, cottagecore interiors |
- Switch off power at the breaker before installation. A licensed electrician is recommended — the electrical cord runs inside the spring tube and connects to the ceiling junction box at the top.
- Once installed and powered, adjust hanging height by hand: pull the shade downward to extend the spring, or push upward to compress it. The spring holds its position through tension — no locking needed.
- For dining tables, pull the shade so the bottom sits 70–80 cm (28–32″) above the tabletop. Raise for ambient lighting when the table is not in use.
- Screw the included E26 or E27 3000K LED bulb into the socket. To dim, replace with a Triac-dimmable E26 or E27 LED and pair with a Triac wall dimmer.
- Dust the fabric shade with a soft brush or low-suction vacuum. Spot-clean with a barely damp cloth — do not soak. Wipe the wood bead drop and hardware with a dry microfiber cloth.
The pendant hangs from a coiled black spring tube. Pull the shade downward to lower it; push upward to raise it. The spring holds position through tension with no locking mechanism. The tube extends up to 1.5 m and compresses to roughly 30 cm when fully raised. All height adjustments are done by hand after the initial hardwired installation.
Does it need an electrician to install?Yes — this is a hardwired pendant. The electrical cord runs inside the spring tube and connects to your ceiling junction box. A licensed electrician is recommended for the initial installation. All height adjustments afterwards require no tools and no further electrical work.
Is a bulb included?Yes — a 3000K warm-white E26 or E27 LED bulb ships with every pendant. Any standard E26 or E27 base also fits.
Which size should I choose?The Ø40 cm suits a 2-person table or bedside. The Ø50 cm is the most versatile for a 2–4 person table. The Ø60 cm works over a 4–6 person table or as a bedroom focal point. The retractable spring lets you fine-tune height after installation.
Is it dimmable?The included bulb is non-dimmable. Swap it for a Triac-dimmable E26 or E27 LED and pair with a Triac wall dimmer to add dimming.
Sizing & questions
Every piece is made to order in our own atelier — here is what most clients ask before choosing theirs.
What size should I choose for my dining table?+Small (Ø 15.7″) suits 2-person tables; Medium (Ø 19.7″) fits 2–4 person tables; Large (Ø 23.6″) works over 4–6 person tables. Hang the shade 28–32″ above the tabletop for task lighting.
How do I adjust the pendant height?+The retractable spring tube extends up to 1.5 m (59″) from the ceiling canopy. Simply pull the shade down to lower it or push up to raise it—no tools or rewiring needed at any time.
Can I dim this pendant?+Yes. Replace the included 3000K LED with a Triac-dimmable E26 or E27 LED bulb and pair it with a compatible Triac wall dimmer switch for full brightness control.
What's included, and how do I install it?+A warm-white E26 or E27 3000K LED bulb ships with every pendant. The fixture hardwires to a ceiling junction box; a licensed electrician is recommended for the initial electrical connection.
Can I customize this pendant for my space?+Yes. Our Vakkerlight atelier builds each pendant to order. Contact us to discuss custom sizing, finishes, or other specifications to suit your room perfectly.
Questions about this product
Is Printed Fabric Petal Pendant Lamp in stock?
Yes — 41 units are available and ready to ship from our US warehouse.
How fast will Printed Fabric Petal Pendant Lamp ship?
Orders placed before 3:00 PM ET ship the same business day. Delivery takes 3–5 business days inside the USA.
What colour options does Printed Fabric Petal Pendant Lamp come in?
Available colour: Beige. 3 variants in total, each with its own SKU and price.
How much does Printed Fabric Petal Pendant Lamp cost?
Prices run from $35.90 to $48.90 depending on the variant.
Where does Printed Fabric Petal Pendant Lamp ship from?
It ships from the United States. Standard delivery is 3–5 business days, and orders placed before 3:00 PM ET go out the same day.
All variants (3)
| Size | Colour | SKU | Price | Stock |
|---|---|---|---|---|
| Ø 15.7″ x H 59″ | Beige | VKP1-2673-01 | $35.90 | In stock |
| Ø 19.7″ x H 59″ | Beige | VKP1-2673-02 | $42.50 | In stock |
| Ø 23.6″ x H 59″ | Beige | VKP1-2673-03 | $48.90 | In stock |